This page collects the parts for turning a Chevy Silverado 1500 or GMC Sierra 1500 into a camping and overland truck: the rack or topper everything else hangs from, drawers and rails for the bed, a flat aluminum panel for the tailgate, and the add-ons that bolt onto the rack. Comparing racks only? Our Chevy Silverado & GMC Sierra 1500 bed racks page lines them up with prices, heights and cover fit.
A Silverado or Sierra 1500 build, layer by layer
-
The platform. Most builds start with an open XTR1 rack at 17" or 23", or at any whole-inch height between 10" and 26" with the Custom Height version. Running a Retrax XR? The XTR3 for Retrax XR adds a center pair of uprights and a 1,750 lb parked rating. XBRS bars stay low at 6" or 8" and can become an XTR1 later. For a lockable shell rather than an open rack, look at the XO.SKLTN (2007 and newer, mid or full height).
-
Somewhere to sleep. On a 2008-or-newer truck, a 23" XTR rack carries a rooftop tent 1" above the cab roof, so the tent can run forward over the cab. Stainless Rooftop Tent Brackets bolt it down: four for $49.90, or eight in the Off-Road Kit for $98. Want your gear under a roof instead? The XO.SKLTN closes up with side panels, a roof section and three locking hinged doors (driver side, passenger side and rear), either ordered with the rack as Stage 2A or 2B or added later with the XO.SKLTN Topper Panel Add-On Kit.
-
Storage in the bed. XTR racks and the XO.SKLTN mount to the bed rails and leave the floor alone, so the bed below stays open for a DECKED drawer system, made for 5.5, 6.5 and 8-ft beds on every body style back to 1999. On 2019+ trucks, Integral's bedside rails bolt into the factory holes along the bed walls for sliding tie-down cleats, and the Integral bulkhead plate holds Packout organizers against the front of the bed. The bulkhead plate can't go in with a Retrax or any other retractable cover.
-
Gear on the rack. Every bar on an XTR rack is T-slotted, so MOLLE plates, AXS side gates, slide-out trays, a Rotopax plate for fuel or water and a recovery board mount bolt on wherever they fit your load. The XTR Awning Upright Kit lifts an awning on 8" to 18" uprights and holds 60 lb, or 100 lb for a 270° awning once you add its support braces. It fits XTR1 and XTR3 racks only, not XBRS or the XO.SKLTN.
-
The tailgate. On 2019+ trucks, the TrailGate panel covers the uneven tailgate with 1/8" powder-coated aluminum, giving you a camp table, a place to kneel and a level spot for an air mattress. Pick the Standard or Multi-Flex / Multi-Pro version to match your tailgate. It starts at $299 and is now built in Wichita next to our racks.
Planning your 1500 build
Open rack or XO.SKLTN topper for a camping truck?
An XTR rack keeps both sides of the bed open and is the usual base for a rooftop tent. The XO.SKLTN shuts your gear behind locking doors that open from both sides and the rear. If you're also weighing a fiberglass cap, our post on bed racks vs overland toppers vs fiberglass toppers goes through the trade-offs.
Can I buy the XO.SKLTN open now and enclose it later?
Yes. Order Stage 1A (rack only) or Stage 1B (rack with MOLLE panels), then add the Topper Panel Add-On Kit for your model, bed and rack height when you're ready. The kit fits the XO.SKLTN only, not XTR1 or XTR3 racks. We lengthened the XO.SKLTN frame for 2018-and-older medium beds by about 0.7", and panels are cut to the current frame, so owners of an earlier rack should measure it or send us the original order number first.
How much can a full build weigh?
Two limits apply. The rack's rating covers what rides on it: an XTR1 carries 450 lb off-road, 850 lb on pavement and 1,550 lb parked, spread evenly. Your truck's payload, printed on the sticker in the driver's door jamb, covers everything at once: rack, tent, drawers, water, tools and passengers. A DECKED system by itself weighs about 200 lb. The overlanding payload guide shows how to add it up.
My Silverado has the 8-ft bed. What still fits?
We don't build XTR racks or the XO.SKLTN for the 8-ft box (email us and we'll tell you what fits). The DECKED drawer system comes in an 8-ft size, and the TrailGate panel is chosen by tailgate style rather than bed length, so a 2019+ long-bed truck can still take one.
Do these parts fit a 2500HD or 3500HD?
The racks and the XO.SKLTN here are made for the 1500. HD trucks have their own: see Silverado and Sierra 2500HD / 3500HD bed racks.
Can I see the rack and accessories together before I order?
Yes. The 3D bed rack builder lets you lay out an XTR rack with plates, gates and trays, then add it to your cart.
Still choosing a cover to run under the rack? See Silverado and Sierra 1500 bed covers. Every rack on this page comes out of our shop in Wichita, Kansas, and XTR1 and XTR3 racks are backed by our Lifetime Warranty. Planning a build and want a second opinion? Email support@xtrusion-overland.com or call (316) 330-0024.